MISSISSIPPI LEGISLATURE
2018 Regular Session
To: Agriculture
By: Senator(s) Branning, Jackson (11th)
AN ACT TO AMEND SECTION 63-5-33, MISSISSIPPI CODE OF 1972, TO INCREASE THE WEIGHT TOLERANCE ALLOWED FOR VEHICLES OPERATING UNDER A HARVEST PERMIT AND CERTAIN VEHICLES LOADING AND UNLOADING AT A STATE PORT; TO AUTHORIZE THE TOLERANCE FOR HARVEST PERMIT VEHICLES THAT ARE LOADED AT A POINT OF ORIGIN WITH SCALES AVAILABLE FOR WEIGHING EACH INDIVIDUAL AXLE; AND FOR RELATED PURPOSES.
BE IT ENACTED BY THE LEGISLATURE OF THE STATE OF MISSISSIPPI:
SECTION 1. Section 63-5-33, Mississippi Code of 1972, is amended as follows:
63-5-33. (1) Subject to the limitations imposed on wheel and axle loads by Section 63-5-27, and to the further limitations hereinafter specified, the total combined weight (vehicles plus load) on any group of axles of a vehicle or a combination of vehicles shall not exceed the value given in the following table (Table III) corresponding to the distance in feet between the extreme axles of the group, measured longitudinally to the nearest foot, on those highways or parts of highways designated by the Mississippi Transportation Commission as being capable of carrying the maximum load limits and, in addition thereto, such other highways or parts of highways found by the commission to be suitable to carry the maximum load limits from an engineering standpoint, and so designated as such by order of the commission entered upon its minutes and published once each week for three (3) consecutive weeks in a daily newspaper published in this state and having a general circulation therein. The maximum total combined weight carried on any group of two (2) or more consecutive axles shall be determined by the formula contained in the Federal Weight Law enacted January 4, 1975, as follows: W=500 (LN/N-1+12N+36) where W=maximum weight in pounds carried on any group of two (2) or more axles computed to the nearest five hundred (500) pounds, L=distance in feet between the extremes of any group of two (2) or more consecutive axles, and N=number of axles in any group under consideration.
TABLE III
DISTANCE
IN FEET
BETWEEN THE
EXTREMES OF
ANY GROUP
OF 2 OR MORE
CONSECUTIVE MAXIMUM LOAD IN POUNDS CARRIED ON ANY
AXLES GROUP OF 2 OR MORE CONSECUTIVE AXLES
2 axles 3 axles 4 axles 5 axles 6 axles 7 axles
4 34,000
5 34,000
6 34,000 Axle groups in
7 34,000
8 and
less 34,000 34,000 these spacings
More
than
8 38,000 42,000
9 39,000 42,500
10 40,000 43,500 impractical
11 44,000
12 45,000 50,000
13 45,500 50,500
14 46,500 51,500
15 47,000 52,000
16 48,000 52,500 58,000
17 48,500 53,500 58,500
18 49,500 54,000 59,000
19 50,000 54,500 60,000
20 51,000 55,500 60,500 66,000
21 51,500 56,000 61,000 66,500
22 52,500 56,500 61,500 67,000
23 53,000 57,500 62,500 68,000
24 54,000 58,000 63,000 68,500 74,000
25 54,500 58,500 63,500 69,000 74,500
26 55,500 59,500 64,000 69,500 75,000
27 56,000 60,000 65,000 70,000 75,500
28 57,000 60,500 65,500 71,000 76,500
29 57,500 61,500 66,000 71,500 77,000
30 58,500 62,000 66,500 72,000 77,500
31 59,000 62,500 67,500 72,500 78,000
32 60,000 63,500 68,000 73,000 78,500
33 64,000 68,500 74,000 79,000
34 64,500 69,000 74,500 80,000
35 65,500 70,000 75,000 80,000
36 66,000 70,500 75,500 80,000
37 66,500 71,000 76,000 80,000
38 67,500 71,500 77,000 80,000
39 68,000 72,500 77,500 80,000
40 68,500 73,000 78,000 80,000
41 69,500 73,500 78,500 80,000
42 70,000 74,000 79,000 80,000
43 70,500 75,000 80,000 80,000
44 71,500 75,500 80,000 80,000
45 72,000 76,000 80,000 80,000
46 72,500 76,500 80,000 80,000
47 73,500 77,500 80,000 80,000
48 74,000 78,000 80,000 80,000
49 74,500 78,500 80,000 80,000
50 75,500 79,000 80,000 80,000
51 76,000 80,000 80,000 80,000
52 76,500 80,000 80,000 80,000
53 77,500 80,000 80,000 80,000
54 78,000 80,000 80,000 80,000
55 78,500 80,000 80,000 80,000
56 79,500 80,000 80,000 80,000
57 80,000 80,000 80,000 80,000
(2) Moreover, in addition to the per axle weight limitations specified by Section 63-5-27, two (2) consecutive sets of tandem axles may carry a gross load of thirty-four thousand (34,000) pounds each, providing that the overall distance between the first and last axles of such consecutive sets of tandem axles is thirty-six (36) feet or more, except that, until September 1, 1989, the axle distance for tank trailers, dump trailers and ocean transport container haulers may be thirty (30) feet or more. Such overall gross weight may not exceed eighty thousand (80,000) pounds, except as provided by this section.
(3) Notwithstanding the
provisions of Section 63-5-27 and/or Section 63-5-29 to the contrary, vehicles
hauling products in the manner set forth in this subsection, whether or not
such vehicles are operating with a harvest permit, shall be allowed a gross
weight of not to exceed forty thousand (40,000) pounds on any tandem. Vehicles
operating without a harvest permit shall be allowed a tolerance not to exceed
five percent (5%) above their authorized gross vehicle weight, tandem or axle
weight; except that the maximum gross vehicle weight of any such vehicle shall
not exceed eighty thousand (80,000) pounds plus a tolerance thereon of not more
than two percent (2%). Vehicles operating without a harvest permit loading
at a point of origin having scales available for weighing the vehicle shall not
be eligible for any tolerance over the gross weight limit of eighty thousand
(80,000) pounds. Vehicles operating with a harvest permit shall be allowed
a tolerance not to exceed * * *five percent (5%) ten percent (10%) above their
authorized tandem or axle weight, but the maximum gross vehicle weight of any
such vehicle shall not exceed eighty-four thousand (84,000) pounds. However,
neither the increased weights in this subsection nor any tolerance shall be
allowed on federal interstate highways or on other highways where a tolerance
is specifically prohibited by the Transportation Commission, the county board
of supervisors or the municipal governing authorities as provided for in
Section 63-5-27. The tolerance allowed by this subsection shall only apply to
the operation of vehicles from the point of loading to the point of unloading
for processing, and to the operation of vehicles hauling sand, gravel,
woodchips, wood shavings, sawdust, fill dirt, and agricultural products,
and products for recycling or materials for the construction or repair of
highways. The range of such operation shall not exceed a radius of one hundred
(100) miles except where the products are being transported for processing
within this state. * * *
(4) Notwithstanding the
provisions of Section 63-5-27 and/or Section 63-5-29 to the contrary, vehicles
hauling prepackaged products, unloaded at a state port or to be loaded at a
state port, which are containerized in such a manner as to make subdivision
thereof impractical shall be allowed a gross weight of not to exceed forty
thousand (40,000) pounds on any tandem, and a tolerance not to exceed * * * ten percent (10%)
above their authorized gross weight, tandem or axle weight; except that the
maximum weight of any vehicle shall not exceed eighty thousand (80,000) pounds
plus a tolerance thereon of not more than two percent (2%); however, neither
the increased weights in this subsection nor any tolerance shall be allowed on
federal interstate highways or on other highways where a tolerance is
specifically prohibited by the Transportation Commission, the county board of
supervisors or the municipal governing authorities as provided for in Section
63-5-27.
(5) (a) Vehicles for which a harvest permit has been issued pursuant to Section 27-19-81(4) shall be allowed a gross vehicle weight not to exceed eighty-four thousand (84,000) pounds. However, the board of supervisors of any county and the governing authorities of any municipality may designate the roads, streets and highways under their respective jurisdiction on and along which vehicles for which a harvest permit has been issued may travel. This subsection shall not apply to the federal interstate system.
(b) Any owner or operator who has been issued a harvest permit and who wishes to operate a vehicle on the roads, streets or highways under the jurisdiction of a county or municipality at a gross vehicle weight greater than the weight allowed by law or greater than the maximum weight established for such roads, streets or highways by the board of supervisors or municipal governing authorities, shall notify, in writing, the board of supervisors or the governing authorities, as the case may be, before operating such vehicle on the roads, streets or highways of such county or municipality. In his notice, the permit holder shall identify the routes over which he intends to operate vehicles for which the permit has been issued and the dates or time period during which he will be operating such vehicles. The board of supervisors or the governing authorities, as the case may be, shall have two (2) working days to respond in writing to the permit holder to notify the permit holder of the routes on and along which the permit holder may operate vehicles for which a harvest permit has been issued. Failure of the board of supervisors or the governing authorities timely to notify the permit holder and to designate the routes on and along which the permit holder may operate shall be considered as authorizing the permit holder to operate on any of the roads, streets or highways of the county or municipality in accordance with the authority granted to the permit holder by the harvest permit.
(c) Anytime a timber deed is filed with the chancery clerk, the grantee, at that time, may make a written request of the board of supervisors of the county or the governing authorities of the municipality, as the case may be, for the purpose of providing to the grantee, within three (3) working days of the filing of the request, a designated and approved route over the roads, streets or highways under the jurisdiction of the county or city, as the case may be, that the grantee may travel for the purpose of transporting harvested timber. Upon providing such route designation, the county or city, as the case may be, shall also provide to the grantee a map designating the approved route. An approved route designation provided to a grantee under the provisions of this paragraph shall be valid for a period of six (6) months from its date of issue. The permit authorized to be issued under paragraph (b) of this subsection shall not be required for any person who obtains a permit issued under this paragraph.
(d) This subsection
(5) shall stand repealed from and after July 1, * * * 2022.
(6) Nothing in this section or subsections (1) through (4) of Section 63-5-27 shall be construed to deny the operation of any vehicle or combination of vehicles that could be lawfully operated upon the interstate highway system of this state on January 4, 1975.
SECTION 2. This act shall take effect and be in force from and after July 1, 2018.